How To Install Turbine Vents
The installation of a turbine vent is nearly identical to a static vent. A roofer will, from the attic, mark a spot near the ridge of the roof . From the roof, the roofer will cut away shingles and underlayment, and use a saber saw to cut a hole the same size as the diameter of the vent.
Following manufacturers instructions for securing the vent, the roofer will likely spread plastic roof cement on the underside of the vent, place it over the hole, slip the flange under the top-side shingles, and lay the flange over the down-slope shingles.
The roofer will then nail the base in place with galvanized roofing nails and cover nail heads with roofing cement.
” rel=”nofollow”> House Logic)
Screw The Ductwork Together
Connect the ductwork with sheet metal screws, wrap the connections with aluminum faced duct tape, then wrap the attic part of the duct work with an insulated sleeve. Here are our tips on installing round ductwork, too.
If you want to replace the range hood and exhaust fan above your stove and vent it to the outside, and the stove is against an interior wall, you have several options. But the rule of thumb is to route it the shortest and straightest path to daylight. That way, youll get the best airflow and the least amount of grease buildup for your kitchen fan vent.
From the inside wall of a ranch house , that route usually means going up through the attic and out the roof. You could also go up into the cabinet above the stovethen horizontally to the closest exterior wall, either through the cabinets or in the area above the cabinets. Unfortunately, running the vent that way eats up valuable cabinet space, and it can be tricky to install, especially if you attempt to run it in the soffit area because of obstacles.
Whichever route you choose, make sure the total duct length doesnt exceed the fan capacity. The owners manual will usually tell you specifics on duct sizes and lengths. First, plan your route. The safest way to check the attic directly above the stove is to chuck an 18-in. section of straightened coat hanger into a drill. Loosely hold the wire and direct it through the ceiling drywall approximately where your vent pipe will go.
Locate The B Vent Route
Plan the route the b vent will take from the appliance to the roof. Most manufacturers and building codes require that you locate the b vent roof opening as close to the appliance as possible. A straight vertical run is the best option. Avoid any bends or slants in the vent pipe.
If you must route the b vent around obstacles, follow the manufacturers recommendations on the types of connectors and the installation of any elbows or unions in the pipe.
Some manufacturers accept the use of special types of flexible vent pipe with their systems. Only use flexible pipe when the manufacturer specifies the type of flexible vent pipe to use.
Recommended Reading: Exposed Fastener Metal Roof Screw Pattern
How To Vent A Range Hood Through The Roof Or A Side Wall
The next time you decide to show off your Hibachi Chef talents and cook that delicious meal for a small gathering of friends in your kitchen, make sure your kitchen is properly equipped to handle all the smells, steam, and oil splashes from your grand hibachi art-work!
In other words, youll want to make sure that your kitchen space is 100% ready for the hard-core cooking, so that when its all said and done, your kitchen still looks, feels, and smells great!
That being said, I would like to talk about a proper way to vent a kitchen hood, so that you dont end up with all sorts of messy stains and unwanted moisture and smells in your lovely kitchen.
It is essential to properly vent your range hood, so that any smoke, fats, vapors, and grease produced whenever you cook, dont create an unwanted settlement and unsightly stains on the ceiling in your kitchen. Trust me, you dont want to ever let any of that to happen to your kitchen!!!
Range hoods are typically vented using a special duct work that runs through a roof, and less often, through an exterior wall of your house. The duct work is usually concealed within the walls, and it is really important to make everything air and water tight. This way, you wont have to come back to fix any deficiencies after everything is set and done.
Installing a new roof vent will require either hiring a roofing contractor or doing it yourself provided you are handy and can exercise proper safety precautions while on the roof.
Bore A Hole On The Ceiling
To successfully carry out this step, youll need several tools for various types of ceilings. You sure dont intend to use the same tool for a wood type and a concrete one, because that wont be good.
So if youre done with making the necessary punctures, you should prepare for the ceiling outlet. The task might be a little bit tough for a first-timer, just try to give it your best and drill an opening that lets the range hood outside the ceiling.
Recommended Reading: Proper Screw Placement Metal Roofing
Range Hood Vent Installation
Installing a roof vent will require you either doing it on your own if you are handy and are able to be safe or hiring a roofing contractor to do it for you. Artistic Alloys & Design custom designs, fabricates, and installs all of our range hoods for your convenience. Our team ensures the installation is correct so you get the maximum benefit from your new range hood.
Most ducts will be 10 inches wide and shaped in an accordion round duct. You will also need a 10-inch roof vent, made from painted steel and not plastic. You need to figure out where you are going to place your roof vent, as it needs to be 3 feet from the nearest roof items such as chimneys, skylights, bathroom vents, and away from the valleys of the roof and between rafters.
A roof vent that is not installed correctly can cause roof leaks which means that you have to repair the roof to deal with the issue.
Also, you want to make sure that your kitchen vent is 5 feet your roof eaves. That means 5 feet from the slope of the roof and away from the edge.
Once you have found the right location for your vent and it has been marked, drill a hole into your roof from the inside of your attic which is located between 2 rafters. Once the hole is drilled, you will have to cut the right sized opening to fit the hood vent either round or square shaped based on the design.
How Do You Install A Roof Vent
How to Install a Vent Pipe Through a Roof
- Go into your attic.
- Cut through the plywood and roofing material with your reciprocating saw.
- Measure the length of your roof shoe with a tape measure.
- Climb onto the roof.
- Lift up the shingles.
- Have a helper in the attic slide the vent pipe up through the roof shoe from below.
Don’t Miss: How To Repair Roof Trusses
Wrap Up The Procedure And Clear Up The Mess
After you have mounted the range hood vent, make sure to settle any device you may have deconstructed for safety reasons. For instance, the fan in the kitchen Put it back to its original place and clean up the kitchen space, which may have any cement debris or dust and other equipment.
To conceal all the wires and the rest of the work from venting, you can simply pull down the chimney to the top of the hood.
Once the whole installation process is over, it is important to clean up the remaining garbage, such as debris from drilling and other tools and equipment. If your kitchen is not clean after installing the range hood vent, then the whole process of installing it becomes worthless.
Apart from making your kitchen look better and protecting the tools to make them last longer, cleaning up the post-installation works also has another main benefit. You can avoid potential injuries to yourself that might be caused by sharp items lying on the floor as part of the debris.
Do I Vent My Range Hood Through The Wall Or Roof
You have two options to vent your range hood: through the wall or through the ceiling.
Wall and under cabinet range hoods vent through the wall or ceiling, while island range hoods must be vented through your ceiling.
When choosing how to vent your wall range hood, there are a few things to consider. What is the shortest distance from your kitchen to the outside, with the least amount of turns or elbows? Find this distance and your hood will run at its optimal efficiency.
Second, do you have anything obstructing your ductwork? You want to pick a path that is completely unobstructed to allow for a smooth and affordable installation.
Recommended Reading: Roofing Costs In California
A Note About Bathroom And Kitchen Exhaust Vents
Bathroom and kitchen exhaust vents are not a type of roofing vent. It should be noted that these vents, which expel warm moist air from the bathroom and food prep areas of the home, need their own ducts and vent hoods, which direct air to the homes exterior. These vents and ducts should never share space with the roof vent, and air should never be vented directly into the attic.
What Is The Best Roof Vent Cap
The best roof vent cap is the Builders Best Roof Vent Cap. It is available in both 4 and 6 diameter, which makes it a great fit for range hoods up to 900 CFM. This roof cap is manufactured with a durable galvanized steel. Its a reliable option for your range hood.
Buy your Builders Best roof cap .
You May Like: Skylight In Metal Roof
Why Should You Consider Venting Your Range Hood Through The Ceiling
Venting your range hood through the ceiling will regulate your kitchen air like never before. Since range hoods essentially take in all fumes from the cooking process, chances are that grime can accumulate on the insides of these range hoods. To avoid this, it is best to vent your range hood through the ceiling â this will give the duct access to the fresh, clean air that can avoid the accumulation of dirt inside the duct system.
Not only will there be a minimal accumulation of dirt, but this will also ensure durability for your range hood. With the grime out of the way, your range hood will also have the opportunity to breathe clean air.
However, venting your range hood through the ceiling comes at a heavier price on your pocket. You have to take into account the cost of ducting, installing vent caps, and other such overhead expenses. The exact opposite of what recirculating under cabinet range hoods offer. Sure enough, however, this is a high investment high returns situation.
Builders Best Roof Vent Cap
The best roof vent cap is the Builders Best Roof Vent Cap. It is available in both 4 and 6 diameter, which makes it a great fit for range hoods up to 900 CFM. This roof cap is manufactured with a durable galvanized steel. Its a reliable option for your range hood.Buy your Builders Best roof cap .
Read Also: Mobile Home Ceiling Panels Sagging
Section : How To Install A Range Hood Vent Through The Wall
If you find it hard climbing the roof to be able to vent your range hood, then you can vent it through the wall. Another name for venting through the wall is called horizontal wall venting. All you need to do is install an 18 inches straight venting before installing an elbow.
This is another method of installing for installing an elbow that would later go into the wall. You can also run the duct through the ceiling using the guide in section one and then connect it to an exterior wall nearby.
Getting started, you should make a hole a little larger for the ducting of your vent. After doing so, attach the venting unit using flat head screws around the edges to the mounting box, making sure they are at least three inches apart.
Before attaching the ducting through the venting hole, we advise you to trim the vents flange so that it can perfectly fit the mounting box. Apply clear roofing graded caulk so that it would seal the vent and the mounting box.
We also recommend getting a vinyl mounting box that is 12×18 inches and cut it down into a round hole ready for the ductwork. Most of the ductworks are 10 inches wide and are usually shaped in an accordion way. You should also make sure the roof vent is of the same size as what you have bored down.
Roof Vent Hood Details
The best exhaust fan venting is through smooth, rigid ducts with taped joints and screwed to a special vent hood. Although this isn’t always possible in attic crawl spaces, you should always insulate the duct to prevent condensation problems. You can find 4-in. duct already wrapped in insulation at home centers. If you’re tempted to vent your exhaust fan through an existing roof vent, or even vent it into the attic, don’t do it. First, you’ll partially block your roof vent with the piping, reducing the flow of cooling air through your attic. Second, during cold winters, you’ll be blowing warm, moist air onto a cold surface . The water will condense and drip into the insulation below and perhaps into the house. Special bathroom fan roof vents with an internal damper that opens only when the fan is blowing will send moist air outdoors and keep cold air out of the house.
Don’t Miss: How Much Weight Can An Old Mobile Home Roof Hold
Ducted Or Vented Hoods
This type of venting is typically the vertically ventilated hood, which we very much like, but they require installation. Even though they require work, this type of ducted hood is usually the most efficient.
They easily trap grease and other unwanted odors to the outside while decreasing the number of times you need to clean your kitchen surfaces.
Investing in the vented hoods also makes sure you do not have to change your filters very often. Having your ducted installation usually cost anything between $1000 and $2000 for a complete job, but in this article, we will be walking you through the step by step process, so save these. Stay tuned.
Can An Acoustic Ceiling Go Over A Kitchen Hood
Yes, you shouldnt have any problems installing a kitchen hood in a room with an acoustic ceiling. In fact, acoustics are designed to reduce echo so it may even dampen the sound of your range hood blower. If the acoustic panels are close to the hood, you may have to clean them pretty consistently. Or, you can keep your hood on a higher speed to ensure that all the grease and dirt vents to the outside.
Recommended Reading: Metal Roof Skylight
Broan 437 High Capacity Roof Cap
Perhaps the priciest product on this list, this kitchen hood roof vent cap is designed with state-of-the-art technologies in order to provide you the best service for a long time. You truly get your moneyâs worth with this one â the bird screen is top-notch and the product is made to handle exceptional amounts of CFM. It promises you extreme durability.
A common problem that was noticed with this product, however, is the vent opening is not circular like most vent roof caps. Itâs rectangular and can prove to be a hindrance during the installation process, so keep that in mind before purchase â since this is a high investment indeed!
Hvac Contractor Will Handle Everything
HVAC contractors take the hassle out of dealing with multiple tradespeople and get things done quickly. The work done by them is often of higher quality than compared to a general contractor since they work with things like this every single day.
Since installing a range hood could mean that new wires must be run from the electrical panel, the HVAC contractor might call in an electrician for that part of the job. However, In most cases, you will only need to deal with one person and pay once for everything.
This all-in-one package is perfect for those who are too busy to be bothered with the details and can afford the extra cost.
You May Like: Shingling A Shed
Ductless Or Recirculated Hoods
Ductless hoods do not use the same concepts as ducted vents. This is because they do not need any vents installed, but they still trap the needed grease and smoke away.
How they do this is that they draw the odors and smoke, filter it before recirculating into our homes. These ductless models do not need the regular ductwork that is required by the ducted hoods.
Installing these hoods are much cheaper compared to the ducted vents but are not as effective. They also need a constant change of their filters , which costs about $20, or they can be cleaned even though this option is not advisable.
For more details about ductless and ducted range hoods check out our detailed guide on Ducted vs Ductless Range Hoods as it will help you make a better buying decision.
Diy Vs Hire A Range Hood Installer
The most important consideration in deciding whether to install a range hood yourself or hire a professional is the type of hood youre installing. An experienced DIYer may be able to install a ductless hood because this type only requires you to connect the wiring and secure the hood in place. However, a vented hood usually requires the installer to cut through masonry, which a range hood installer in your area should perform. Routing the ductwork is also a job you should leave to a pro.
Read Also: Briarwood Pro Shingles