Does My Metal Roof Need An Underlayment
The simple answer is yes, your roof does need an underlayment. But there are some caveats that go with that, and it depends on a variety of factors.
Traditionally built homes will need an underlayment. If your home is built with joists, insulation between those joists, and sheathing, then an underlayment is needed before you put on a metal roof. Basically any house in Montana, from Billings to Philipsburg to Zortman is going to be built this way. But there are parts of the home that differ.
A covered patio may not need an underlayment. If your patio has open beam architecture, and is designed to have a roof consisting of structural metal panels then you dont need an underlayment.
If your metal roof is going on top of asphalt shingles, then there is already an underlayment, and it likely doesnt need another. Keep in mind, however, that expansion and contraction of the shingles could cause damage to the back of the metal over time. Its for this reason that Beartooth Metal Roofing in Billings always tears off the old shingles before applying a new roof.
There are some metal manufacturers that require an underlayment in order to keep the warranty valid. Some go even further and require a self-adhering underlayment throughout the entire roof deck. It is a more expensive method, but it will last a whole lot longer and be a whole lot more weather proof.
How Do You Attach Corrugated Metal To A Wall
Start at the bottom of the wall, and install the first strip one inch above floor level. Install the rest of the strips 24 inches apart, and finish with an additional strip at the top of the wall. Insert a screw in a furring strip every place it crosses a wall stud. Studs are typically 16 or 24 inches apart.
Install The Remaining Panels
Install the following line of panels now and work your way up. After finishing that, go back down to start the next one. Youll have to align the panels, overlapping the edge for about 14 inches.
Start the next column by fixing the first left side-rib of the new panel over the last rib of the previously installed panel. In this way, repeat each panel until you cover the whole roof.
You May Like: How Much Does A Commercial Roof Cost
Using The Wrong Substrate Or Underlayment
Metal roofing panels are usually designed to be installed over a solid substrate such as plywood. They can also sometimes be installed over battens rather than solid wood surfaces. As a general thumb rule, however, it is best to put them over a solid surface – particularly for smaller buildings like homes or garages.
Metal roof panels that are installed over battens are more likely to develop condensation behind the panels than those that are installed over solid surfaces. This is caused by the temperature difference between the cold metal panels and the warm, moist air that is trapped underneath them. To minimize problems with condensation, opt for a substrate such as plywood or OSB.
Even if you do install the panels over solid wood decking, you should still use an approved underlayment. This will provide additional protection against condensation, minimizing the likelihood of damage occurring.
Position The Gutters & Roof Flashing
At this point, you must install the gutters and downspouts. For downpipes, you can choose from a variety of PVC pipe types. Install the gutters using roofing nails after properly sizing them.
You can now install continuous flashing or drip edges under the roofing felt. Measure the length of the roof and cut the material. Once finished, install them along the border with roofing nails.
Here are some of the standard roof flashing you can choose from-
| Product 1 |
| Product 2 |
These are the best in the market. It will keep the water away from critical areas of your roof.
Read Also: What Is The Best Moss Killer For Roofs
Seven: Cross Checking And Finishing Touches
After you have covered the entire roof, you may want to apply the ridge and keep plastic pipe boot kits where you will be placing the vent pipe. Now that the process has been completed, your new metal roof will look stunning to behold.
If you want to install your metal roof all by yourself, following the steps above can e helpful in making it a reality. The entire idea is to have a sound structure that will give your home top-notch security.
When getting plywood for replacement, you must make sure the material is quality-made and can protect the roof above it. You should never neglect any sign of damage on your plywood, as they can cause serious harm over time.
For you to have a good-looking and sound structured metal roof, the plywood must be thick enough to help the roof withstand its weight, rain, snow, and wind. Always know that a good under-structure is a good support system and therefore must be taken seriously.
Five: Installing The Rest Of The First Panel Column
After the first panel has been installed, you have to move to the next panel and also install it. Work your way toward the top of the roof before returning to the bottom of the roof where you will be installing the next column of the panel.
Align the second panel, assembling it accurately in such a way that it is directly placed above the first panel. Allow their edges to overlap each other about 12 inches apart. Use metal screws to firmly secure the metal, in the same way, you secured the first panel.
Also Check: What To Ask A Roofer
Five: Installing The Rest Of The First Column
With the first panel in place, youll start to install the next panels. Work your way up to the peak of the roof. Then, youll go back down to the bottom to start the next column.
Line up the second panel directly above the first, overlapping the edge about 12 inches. Secure the panel with the metal screws the same way you did the first panel.
Continue installing the panels in this way until you reach the top of the roof. Note: Use the metal snips to trim the final panel . Make sure to measure twice and cut once.
Four: Install The Metal Roof Panel
The moment you are ready to cover the metal panel above the plywood, you will have to increase your work around the roof. Work will begin from the bottom of the roof. Snap a small vertical line using a chalk box and take measurements from the roofs edge.
Afterward, begin by laying the first panel into various placements beneath the sinistral area of the roof. Work up toward the horizontal surface of the roof and partly cover the roofs edge by an inch. Secure the panel with a hardware roofing supply, keep spaces up to about 12 to 16 inches apart.
Also Check: How Much Do Roofing Leads Cost
How To Put Tpo Roofing On Plywood
Follow these steps to ensure that its properly put on top of the plywood:
First Step: is to make sure that your roof can support it.
Whether or not theres enough weight and strength for TPO material should be determined by a professional because they will know exactly how much pressure each type of roofing material requires.
Second Step: you need to make sure that your roof is clean before the installation begins.
This means clearing out any debris, dirt, or even leaves because it can cause problems with adhesion and create a mess for you later on down the line.
Third Step: check for any joints between different sections of plywood so you have a smooth surface ahead of time.
Make sure that all of your plywood is at least ¾ inches thick because anything less will not be strong enough for TPO material which can weigh up to 70 pounds per square foot.
Fourth Step: apply a primer coat followed by a layer of adhesive which creates the initial bond for this roofing material.
Last step: add the final coat on top of this and let it all dry before youre able to go back inside your home without worrying about any problems with moisture or condensation underneath the membrane itself.
This usually requires a professional who has done this before. If TPO roofing is applied incorrectly, it could lead to a number of different problems down the line that you dont want.
Install Edging And Underlayment
Install the underlayment as per the instructions by the manufacturer. If you are installing edging, which is essentially flashing that works with your metal roof panels, then you should first install the eave edging.
When installing your eave edging, youll fit it to the underside of your eave and onto the face it should cover the entire face of your eave. Screw the eave edging to the underside of the eave, through the lip of the flashing. Then nail the faces with stainless steel finishing nails of the same color as your flashing.
Then install your underlayment so that it covers the eave edging edge. Install the rake edging over the underlayment. It attaches in the same way as your eave edging, except that you use roofing screws to face screw the rake flashing. Ensure the eave end of the rake edging goes over the eave edging.
Note that some rake edging may go over the installed metal panels, not under. In that case, install the metal panels first and the rake edging afterwards. It depends entirely on the manufacturer of your metal roofing panel.
Recommended Reading: Should You Replace Skylights When Roofing
By Step Metal Roof Installation
To explain how to install a metal roof, well use a 10×10 shed with a simple gable roof running down the center of the structure, with a 4:12 slope. Well also be using a standard raised rib metal panel that uses exposed fasteners to attach the panel to the roof sheathing.
Keep in mind that you can use either OSB roof sheathing or plywood for a roof deck beneath your metal roof panels. You can install a metal roof directly on top of either. The key is making sure they are at least ½ thick, at a minimum.
You can use furring strips instead of a solid roof deck such as OSB or plywood. If you are not heating your shed, then furring strips are totally acceptable. If you do heat your shed, furring strips greatly increase the amount of condensation youll have on the underside of your metal roof, so they should be avoided in that instance in favor of a solid roof substrate.
How To Install Metal Roofing Over Plywood In London On
Over time, your homes roofing material will age and break down. While it is unfortunate, every London ON home needs to replace its roofs at some point. Learning how to install metal roofing over plywood is essential in ensuring you have adequate roofing protection against the weather and outdoor elements inside your own home.
As reputable and experience roofers in London ON, we only supply this instruction as a referential material. We highly advise homeowners with little to no DIY roofing experience to only call professionals to address their roofing needs to save time and money.
You May Like: Is Red Roof Pet Friendly
How Much Does It Cost
Many homeowners opt for this type of metal roofing due to its durability, low maintenance needs, weather-resistance, and long lifespan.
Many metal roofs are designed to last anywhere from 50-100 years, so choosing the right roofing material for your home is important.
The cost of installing a new metal roof system over plywood will depend on several factors including: size and type of metal chosen, number of layers required , length of run, pitch of the roof, and whether it is a DIY project or you hire out installation.
Set Up Protective Materials
In this step, youll install slip sheets on top of the felt layers. At first lay the felt on the surface of the plywood. Make certain that you cover the entire roof.
Using a roofing knife, cut the underlayment to the roofs dimensions. Hammer the half-inch roofing nails into the substrate afterward.
Place the smooth slip sheets on the felt now. Nail it along the edge of the roof afterward.
Also Check: Does Renters Insurance Cover Leaking Roof
Does A Metal Roof Affect Wifi
Metal roofs are an attractive and long-lasting option for homes, but many homeowners worry these roofs can interfere with Wi-Fi and even cell phone signals, affecting how they use technology in the home. While a metal roof can interfere with a wireless connection, it is unlikely to be the only culprit.
Recommended Reading: How To Rid Moss On Roof
Install The First Panels
Youre now all ready to install the panels. Starting from the bottom of the roof, snap a chalk line. It should be vertical and ¼ inch away from the rake edge. The line should be parallel with the eave.
You should start from the left and work up to the right side.Begin installing the first panel at the roofs base. Overlay the roofs edge by an inch and work toward the ridge afterward.
Drill 1 ½ inch galvanized screws to attach the metal panel to the decking. Place a screw in every 12 to 16 inches interval.
Recommended Reading: How To Strip A Roof
Using The Wrong Fasteners
When installing metal roofing, it is important to use the right fasteners. If you use standard screws, water can easily leak in around them. This can cause your roof to fail.
Always look for fasteners that are designed specifically for metal roof panels. These fasteners usually incorporate a special washer that helps seal the opening, keeping water from getting inside.
Most companies that manufacture roof panels have specific recommendations as to what fasteners you should use with their panels. To get the best results, always follow their recommendations. Don’t try to save money by skimping on fasteners. The quality of the fasteners is every bit as important as the quality of the roof panels themselves.
Install The Metal Roof Panels
Installing the metal roof panel depends on the type of metal roof product you have, but start at the edge and make sure your first panel overlaps the existing edging by an inch, if applicable. Otherwise run your first panel flush with the rake edge of your roof and 1 over the eave if you have gutters 3 if you dont have gutters.
The top of the metal panel should be flush or no more than an inch below the peak of the gable roof. Screw in your panels according to manufacturer directions. See above for rules about how many screws to use our rule was 80 per square of roofing.
If screwing into the rib of the metal panel, be careful to not screw too far and dent the rib and overly compress the neoprene washer. If you have metal panels overlap at a rib you can also use metal lap screws, which connect the panels but do not go into the sheathing. These are also used for roof edging that go over metal roof rake ends.
If your metal roof product says you need mastic tape and sealant to put beneath the panel seams, then go ahead and apply. Do it slowly as the tape can be difficult to work with.
Chances are your final piece of roof will need a lengthwise cut to fit the width of your shed roof. If so, a circular saw with a metal cutting blade works really well. You can also use tin snips but cutting long pieces with snips is awkward and arduous.
Don’t Miss: How Much To Clean Moss Off Roof
Can Metal Roofing Be Installed Over Plywood Answer Here 2021
A strong substrate is required for metal roofing. Maybe you are thinking Can Metal Roofing Be Installed Over Plywood? Well, if you have such a confusion, you are on the right track.
And yes, metal roofing can be put over the plywood deck if it is strong enough to handle the increased weight of the metal panels.
If you are going to install metal roofing, follow the article.
Can I Install A Metal Roof Myself
While most metal roofing styles can be installed as an advanced DIY project, metal roofing installation is complicated and can vary slightly based on the brand of panels or shingles that you select. We recommend that you install a metal roof with one or two helpers and fall protection equipment designed for roof work.
Also Check: Can You Put Solar Panels On A Tile Roof
Also Check: How Much Is A Solar Panel Roof
Failing To Check With Your Insurance Company For Potential Problems Before Installing Your Roof
Insurance companies usually have certain requirements when it comes to the types of roofs that they will and won’t cover. For instance, did you know that some insurance companies won’t cover metal roofs that have been installed over existing shingles.
The best way to avoid any problems is by contacting your insurance agent to talk to them about the terms of your policy. That way, you can find out if there are any specific rules that you need to follow when it comes to choosing materials or installing your roof.
Removed All Unused Roofing Structure
When contractors made your roof, they built roofing structures such as chimneys, vents, and skylights. Unfortunately, youll need to remove all these areas before you can apply your learnings on how to install metal roofing over plywood. If you want to remove them without breaking them apart, youll need the right tools to do so which professionals only possess.
Dont Miss: How To Figure Shingles For A Gable Roof
Also Check: How To Make A Flat Roof
