Question : What About Hail Damage Does A Metal Roof Not Get As Damaged Byhail In Comparison To Asphalt Roofs
The thing is, metal roofs will get damaged by hail just as much as asphalt. Hail storms will undoubtedly put plenty of dents on your metal roof.
The difference is when it comes to your insurance and durability.
With insurance companies, they give you a less expensive insurance rate if you have a metal roof.
A lot of times, they have you sign whats called an appearance waiver, which means even though the hail storm put some major dents on your metal roof, but nothing is cracked or broken, they wont replace it.
The reason for though your metal roof may be badly dented, it can still withstand quite a lot more hail storms.
It just sucks that youll be stuck with a dented metal roof that doesnt look too appealing.
With all that said in comparison to an asphalt roof, if you get hail on it and it gets dented, your insurance will replace it with new shingles.
If youre ok with the dent, then youre all good.
One drawback of having a dented metal roof is if youre planning to put your home on the market. Its going to reduce your curb appeal and overall property value.
How To Properly Install Standing Seam Roofing
The hidden fastener installation has four steps:
Question : Should Homeowners Still Make The Switch To Metal Roofs In The Future Is It A Trend
That all depends on your roof, house, neighborhood, location, and financial situation.
A metal roof doesnt fit into every neighborhood, and it just doesnt fit into every house. Not all homes will look good with a metal roof install, and that can hurt your curb appeal.
It depends on your location too. Here in Austin, people tend to be more conservative and stick with asphalt roofs whereas up in Dallas, homeowners opt-in for the higher end types of roof, and standing seams happens to be the one they like.
In general, making a switch from an asphalt roof to a metal roof is no easy decision for locals here.
But as far as it going into the future?
We believe more and more homeowners will begin to make the switch here in Austin.
What can make the decision much more comfortable is for homeowners to know who theyre dealing with, and only speak to a reputable local roofing contractor who knows what he or she is doing.
A good contractor should be able to educate you, guide you, and give guidance in your best interest. If theyre a bit pushy, you should proceed with caution.
Because at the end of the day, you dont want to be pushed into a $35k metal roof and have to go and replace it in a couple of short years.
Because with a metal roof, once theyre put on, theres really not an easy way to repair them.
You May Like: How To Get Roofing Leads Without Door Knocking
Aluminum Shingles & Standing Seams: Metal Roofing Options
There are a variety of options and metal roofing prices, and if you are considering installing a new metal roof, the variety might seem overwhelming, and there are a lot of reasons to consider getting a metal roof versus shingles, or vice versa.
Knowing the difference between shingles and standing seams is perhaps the first thing that you should learn, and theres more to it than the cost.
After that, you can get into the various types of metal, their appearance, and the available paint finishes, then all of a sudden that are lots of decisions to make.
Compare Standing Seam Metal Roofing To Screw Down Metal Roofing
Fri, May 1, 2020 @ 10:13 AM|Perry
Metal roofing tends to get lumped together into one big group of roofing when in reality there are many different types of metal and categories of metal roofing. Different types of metal roofing have been designed to serve different applications and the best outcome always results from using the right type of metal roofing and profile in the applications it was designed for. There is not a one size fits all metal roof.
Over the last ten to fifteen years a screw down metal or pole down metal as it commonly called has become widely popular and is being used in about every application possible, right and wrong. The result? Leaks on metal roofs that weren’t supposed to ever leak and metal roofs not lasting even half the time that the roofing contractor said they would. A major reason for this is that the pole barn metal or screw down metal is being used in places where standing seam should have been used.
We highly recommend that pole barn metal be used on barns or warehouses whose structures were designed for this type of metal and that standing seam metal roofing be used on homes and businesses with finished interiors and whose roof has solid wood decking or open steel framing typically found on pre engineered metal buildings. In the next few paragraphs we will make three different comparisons between standing seam and screw down type metal roofing.
You May Like: Briarwood Pro Shingles
Was The Painted Finish On The Metal Roof Panels Protected During Installation
Remember, the painted finish on your metal roof systems panels protects the metal. Standing seam metal panels have Kynar 500, while screw down panels have whatever painted finish the manufacturer puts on them.
Scratching or damaging the finish on the panels will expose the fresh steel to dew or moisture in the air, causing them to rust. That makes it crucial that your local roofing contractor takes all the proper precautions to protect the finish during installation.
For example, every evening after finishing for the day, the roof has to be cleaned off. They can’t leave cuts, little triangles, or any type of shavings on the roof because the steel will rust overnight.
No matter which metal roof system you have, its important that its handled carefully during installation. That makes hiring a great local roofing contractor crucial to your metal roof investment.
Formula For Determining How Many Screws Will Be Needed
Here are two easy formulas for determining the amount of metal roofing screws:
Example: 3,000 square feet X 80% = 2,400 screws
Example: 30 roofing squares X 80 screws = 2,400 screws
Do Not Forget To Order Metal To Metal Screws For The Trim And Panel Sidelap
Example: 3,000 square feet divided by three = 1,000 then divide that by 1.5 = 667 screws
You dont need metal to metal screws for the sidelap if using Corrugated. You will only need sidelap screws for R Panel/PBR Panel and Western Rib/7.2 Panel.
Also Check: New Roof Cost California
Which Metal Roofing Is Right For You
If youre trying to decide between standing seam vs exposed fastener roofing, there are a couple main takeaways to keep in mind.
Standing-seam metal roofs are great for heated areas, like your living quarters, as they handle thermal oscillations very well with minimal leakage. Screw-down metal roofs on the other hand, are great to cover unheated areas like garages, and their low cost may justify the occasional leaks and maintenance needed to keep them in working order.
Where To Screw Down Corrugated Metal Roofing And Other Metal Roof Questions Answered
DIY roofing is definitely your thing for your Denver CO home. You’ve been doing it splendidly so far and the results are rewarding each weekend. You’ve just finished putting on the roof sheathes. Next, you’ve rolled the underlayment nicely. Now, you’re just having some problems with where to screw down corrugated metal roofing.
Truth be told, it’s as simple as using a screw drill bit to drive home the screw and keep your roof in place. However, it isn’t that easy. Corrugated metal roof’s exposed fasteners are often the first to introduce leaks into your underlayment and through your attic. Unfortunately, all corrugated metal roofs will introduce this problem sooner or later.
So, how can you deal with it? Where to screw down corrugated metal roofing while making sure no leaks ever happen? The question isn’t where, but what and how to screw down corrugated metal roofing. We’ll answer this along with other common corrugated metal roofing questions below.
Don’t Miss: Best Placement For Screws In Metal Roofing
Can You Put Tar On A Metal Roof
Tar can actually be used on a metal roof, and many people slop the black goop onto valleys, roof-to-wall joints and plumbing vents to prevent or stop leaks, notes William Kibbel III, a home inspector and restoration consultant who serves as vice president of the Tri-County Inspection Co.
Overtightening Or Undertightening Can Both Result In Leak Points
Sinking screws to fasten a metal roof doesnt sound like a very complicated process, so many well-intentioned folks just assume they can take on metal roofing installation as a DIY project. The problem with this assumption is that if you dont have particular training and experience in this area, you could end up doing more harm than good. One of the most common errors revolves around overtightening or under-tightening the screw fasteners.
Most err on the side of overtightening. Its a natural reaction to simply try and sink the screw as far down as it will possibly go. The tighter the screw, the more secure it must be, right? Unfortunately, no. The problem with this approach is that it overcompresses the washer and creates too much stress. This will cause the washer to fail prematurely, or worse, you could break the washer right from the start. Overcompressed or broken washers can easily result in leaks.
You dont want to overtighten, but you really dont want to under tighten your screws either. A screw thats underdriven doesnt create a proper seal for the washer, and that can results in leaks, too. If you can still spin the washer after youve put in your screw, thats a good indication that the screw is still under tightened. A professional installer is able to avoid both extremes by utilizing a specialized screw gun which is set to exact speed and/or torque specifications for metal roofing gasket fasteners.
Also Check: How Far Apart Should Screws Be On Metal Roof
Metal Roofing Costs Vs Shingles
The costs of metal roofing versus the costs of asphalt shingles or other types of shingles are somewhat dependent on your location and the type of property that you have, along with your initial starting budget.
Also, you should keep in mind that metal roofing has a much higher resale value than some other types of roofing, so consider that when you are choosing what type of roof you want to install on your home.
If you are choosing between metal roofing and shingles, keep in mind that metal roofing can be a great choice, because it can pay for itself via energy efficiency.
A metal roof can result in decreased home cooling costs, and it also has a great resale value due to its reliability and longevity.
With a metal roof, you will most likely not have as much of a need for maintenance and repairs, and you will probably not need to replace it as quickly since metal roofing tends to be fairly low risk in regard to premature roof failures and the subsequent need for replacement.
Metal roofing also tends to have a positive resale value if you change your mind or want to replace your roof for aesthetic reasons.
The national average for metal roofing costs around $18,500, but the resale value can possibly offset some of the costs of the initial install.
The lifespan of a metal roof can last from 38 60 years.
Final Thoughts On Standing Seam Vs Exposed Fastener Metal Roofing
So which metal roofing type should you choose? It depends.
Standing seam and exposed fastener metal roofing both have their pros and cons, but if you know what youre looking for and expecting when you go to purchase the roof, youll be better prepared to make the right choice.
Keep in mind:
- Standing seam metal roofing offers a sleek modern look, weather-tight warranty options, space for thermal movement, tested engineering/performance, and no panel penetrations.
- Exposed fastener metal roofing offers a lower price point, opportunities for DIY projects, a roof that performs well, and a traditional look.
At Sheffield Metals, we are here to answer your questions and provide you with peace-of-mind as you go through choosing the right metal roofing type for your structure whether its standing seam, exposed fastener, or another material type.
Read Also: How Much Does A Roof Cost In California
Are Standing Seams Better Than Corrugated Metal
Both standing seam and corrugated metal roofs have their differences. For one, standing seam metal have concealed fasteners, which reduce the likelihood of leaks due to damaged screws. Unfortunately, they have their respective problems homeowners need to deal with in the future.
Sheffield Metals has a great comparison between the two variants of metal roofs. You can read more about them below.
Standing Seam Metal Roofing
Standing seam metal roofs are not fastened by screws, but rather, are interlocked, or hooked, onto one another with each panel. The standing seams are between 12 to 24 inches wide depending on the panel type and the type of aesthetic you prefer.
Fastening is achieved through a 1-inch bend that allows for interlocking. This fastening allows the standing seam metal roofing to move, expand, and contract without breaking tight seals. The fastening on the metal panel system is hidden below the surface of the panel by using a clip or nail flange system. A hidden system is a big plus eliminating the faulty or improperly fastened exposed systems.
Lets compare the two!
Also Check: Garage Roof Trusses
Average Cost Of Materials For A Metal Roof
As described above, the average cost of materials for a metal roof is around $12.00 $13.00 per square foot, but that can definitely vary based on your area, the exact type of material you choose for your metal roof, and the idiosyncrasies of your property, and other environmental factors that impact the final metal roofing quote.
Installation and labor costs also make up a major component of the cost of your new metal roof, regardless of the type of materials that you choose, so take that into consideration when you are getting started on choosing a metal roof or any kind of roof for your home.
That said, knowing the average cost of materials for a new metal roof in the United States is an important starting point!
The national average for a new metal roof is $18,500 , but of course, that varies depending on the type of roofing materials, your location, and your property.
Exposed Vs Hidden Screws
Exposed fastener installation is easier and less expensive. However, when screws are exposed to the weather in Central Texas, they can rust and the washers can crack, leading to leaks that can damage not only the roofing but also the structure of the building. Hidden screws are the proper way to screw down metal roofs. Hidden screw roofing is called “standing seam.”
Recommended Reading: Mobile Home Ceiling Panels Sagging
Can You Screw Into Roof Shingles
shinglesdoshingleroofingwillscrews
. Correspondingly, can I use screws for roof shingles?
Screws on the roof is fine as long as you are screwing threw a shingle. The screw seals itself when going through it because of the mix in shingle gets caught up in thread of screw. Just don’t go crazy with them and use reason and common sense should be ok.
Furthermore, how do you put plywood on a roof? Take two 2x4s long enough to extend above the roof line by about 2. Attach another section of 2×4 across them to hold them together at a height that will allow you to stack the plywood on it so that the top of the plywood sticks up above the top of the jack stand at the roof line.
Also asked, can I screw into epoxy?
Once epoxy hardens, holes may be drilled through the resin. Crafter site ‘Little Windows,’ explains “You can drill holes into or through your resin pieces. Then you can either glue in an eye-screw, or add a jump-ring or a wire through the hole. Epoxy is easy to handle too.
Can I use roofing nails for cedar shingles?
Our cedar shingle nails are slender and still to resist wood splitting. Type 316 Stainless Steel should be used in corrosive environments or when a pressure treatment or a fire retardant treatment has been applied to the wood. Nails should be long enough to penetrate sheathing at least 3/4″.
How To Install Corrugated Roofing
This article was co-authored by . Mark Spelman is a General Contractor based in Austin, Texas. With over 30 years of construction experience, Mark specializes in constructing interiors, project management, and project estimation. He has been a construction professional since 1987.There are 7 references cited in this article, which can be found at the bottom of the page.wikiHow marks an article as reader-approved once it receives enough positive feedback. This article received 20 testimonials and 91% of readers who voted found it helpful, earning it our reader-approved status. This article has been viewed 993,196 times.
Corrugated roofing is a great way to top a garden shed, shop, or patio. It’s quick, easy, low cost, and you can do it yourself. You only need some basic tools and materials.
Also Check: How Much Shingle Roof Cost
