Saturday, March 23, 2024
HomeEditor PicksHow To Install Roll Roofing On A Mobile Home

How To Install Roll Roofing On A Mobile Home

Building A Pitched Mobile Home Roof Over A Flat Roof

How to install a Mobile Home roof using plywood and EPDM Rubber

Flat roofs on mobile homes are a burden because of the re-coatings required. And since flat roofs have no overhang or true gutter system theres a chance that water will flow down the side of the home and either damage the exterior walls, windows, or door or create leaks.

Turning a flat roof into a pitched or peaked roof and adding an overhang is a popular mobile home improvement project. It helps with water runoff and adds value and lifespan to the home.

This single wide went from a flat roof to a pitched roof:

How To Install Metal Roofing

1) Measure the height of the ceiling. Measure the height of the ceiling and add 2 to 4 inches to the measurement to account for the overhang. 2) Build a base. Remove the old clapboard and lay down 30 pounds of tar paper or roofing felt to make the base. 3) Install the metal liner. Use 1¼” metal roofing nails to install the metal trim around the perimeter of the roof. 4) Placing the sheets. When installing the first roofing membrane, the wood screws will be every two feet in the center and inside. 5) Install the metal siding. Then install the metal sheathing around the edges of the roof every 2 feet with 1″ wood screws.

Is Peel And Stick Better Than Hot Mop

Because it requires several layers and hot asphalt, hot mop is a much more labor intensive process than peel and stick underlaymentand it can be more costly, too. Peel and stick underlayment features a longer life span than hot mop, particularly in hot areas like Florida, where heat can degrade asphalt more rapidly.

You May Like: Trailer Roof Repair Cost

How Do You Install Tin Roofing Over Shingles

Screw the metal plates to the truss frame with a wood screw every 2 meters around the edges. Screw the first sheet securely in the center and along the edges. Use tin scissors to cut pipes and exhaust holes. Cut V-shaped notches in the sheet metal and bend them to match the ridge edge and eaves. Cover the bottom of the metal roof.

Roll Roofing Manufacturer’s Installation Instructions & Product Specifications

Job Photos

Illustration: SBS type roll roofing or BUR rolls from MTechnology cited below.

  • BP Slate Surface Roll Roofing and BP Mineral Surface roll roofing and related products are described in BP’s ASPHALT SHINGLE APPLICATION INSTRUCTIONS , Building Products of Canada, Co., 9510, St. Patrick Street, LaSalle , Canada H8R 1R9 and BP Canada 3703-101 Avenue N.E., Edmonton , Canada T5J 2K8, retrieved 2019/05/01 original source:

Suggested citation for this web page

ROLL ROOFING, ASPHALT & SBS INSTALLATION at InspectApedia.com – online encyclopedia of building & environmental inspection, testing, diagnosis, repair, & problem prevention advice.

Or see this

INDEX to RELATED ARTICLES: ARTICLE INDEX to BUILDING ROOFING

Or use the SEARCH BOX found below to Ask a Question or Search InspectApedia

Don’t Miss: How Much Does A Roof Cost In California

How To Repair Rolled Roofing In 5 Easy Steps

Rolled roofing may not be for everyone, but it is still a popular option nonetheless. There are some reasons why it becomes peoples favorite. First, as mentioned prior, it is quite cheap theres no need to break your bank to get roof coverage.

Next, it is quite easy to install without consuming too much time. That means for most times, you should be able to do the roof covering job by yourself without relying on a roofing firm.

Another benefit that you can get is the possibility of repairing rolled roofing on your own. If the roof deck condition is considered good, then the repair must be fairly simple to do. Roll roofing can be cut into strips despite being made from a similar material as asphalt shingles.

Cleaning out the damaged section and filling it with sealant or tar specifically made from roofing must be enough if its only small holes. On the other hand, the larger damaged section may require you to cut the area out and replace it with a new roll roofing part.

Before youre getting started and learn how to repair rolled roofing, make sure youre not working on a wet roof or raining weather. This can turn into a hazardous situation as the roof will become really slick and increase the possibility of severe fall. After that, ensure that the ladder that you are using is secure and strong enough.

  • To secure the new roll roofing, drive nails on every foot of it.
  • Shingled Mobile Home Roof Overs

    A real shingle roof for mobile homes is absolutely possible for most models. They can have a higher pitch or gables too. Shingle roof overs are also installed right over your existing roof, as long as you have not already had a roof over previously.

    The subject of whether its a good idea to add a second layer of shingles is much debated in the roofing industry. Be sure to get an experts opinion on your home before you make a decision. There seems to be a split in opinion on layering the new shingles over the old. Some roofing experts say you can do on manufactured homes that have 2×4 studs 12-16 OC and roof trusses that are 16 OC or less. Others roofing experts have told me they wont do it on any manufactured home.

    If youre set on a shingle roof you come in a few different options and styles for roof overs, as well as several different colors and textures.

    The main benefit of a shingle roof is the appearance. Shingles can dramatically improve the curb appeal of your property. Installing shingles is typically more costly than a TPO or metal roof but can improve the value a little more so you may recoup the costs.

    Its not unusual to see asphalt shingles on a mobile home, particularly on homes with pitched roofs. Because asphalt is frequently used on site-built homes, many people are drawn to their appearance. Asphalt has a class A fire-rating and its available in a wide array of styles and colors.

    Also Check: Skylight Metal Roof

    Installing The Rolled Roofing

  • 1 Using a measuring tape, measure 35 inches up from the bottom of the roof and make a mark with chalk. The measurement of 35 inches is the default measurement used by most roofing professionals. Use a ruler or meter stick to draw the chalk line across the roof.XResearch source
  • Avoid using eaves as guides as they are not necessarily placed at the same height across the roof.
  • 2Apply roofing cement to the roof. Use a trowel to scoop up the roofing cement. Spread the roofing cement along the edges of your roof so itâs about 1â8â1â4 inch thick. You can get roofing cement at the local hardware or building supplies store.XResearch source
  • Apply the cement in stages. Do the bottom part of the roof before you start working on that section, apply it to the middle before you start working there, and so on. Use the chalk lines as the borders of each section.
  • Always wear gloves when working with roofing cement.
  • Read the instructions on the side of the roofing cement container before you begin.
  • 3Cut the rolled roofing to the right size using a razor knife. The rolled roofing should reach the chalk line when you lay it down and should stretch from 1 side of the roof to the other. You’ll need to use plenty of pressure with the razor knife to cut the rolled roofing material.XResearch source
  • The first layer should cover the roof as far as the chalk line.
  • Be careful when working with a hammer and nails on a roof. Make sure you have a stable grip on the roof.
  • How To Install Roll Roofing

    Installing the Metal Roofing – Mobile Home Roof Project

    Roll roofing is one of the easiest types of materials to install. What youll need to keep in mind, though, is that homeowners choose it when they care less about their roofs appearance than other characteristics .

    In this article, were going to discuss what roll roofing is, common materials used to make it, its pros and cons, and a step-by-step guide about roll roofing installation. Well also answer the questions were most frequently asked about it.

    At Legacy Service, we provide roofing installation and replacement services throughout Pennsylvania, New Jersey, and Delaware. If youre interested, please contact us at 215-798-9790 to learn more.

    Don’t Miss: Average Shingle Roof Cost

    How Toinstall Rubber Roofing

    Although it is said that the rubber roofing installation process is not something easy, it is not bad to learn about it, at least, theoretically. There are some basic steps for the installation.

    All of the steps are started by cleaning the roof area like removing the leaves, twigs, and other debris. Aside from the rubber roofing roll, there are some other tools and equipment to be prepared including the drip batten, adhesive tool, nails, hammer, and cutter.

    Read also : How to Install Rubber Roofing

    In installing other types of roof layer, a fiberglass sheet is often used to make sure that the layer is attached well and avoid problems like the growth of the moss.

    In rubber roofing, the additional layer is not needed anyway. So, you can start it all directly by placing the rubber roll. The only thing to install before the layer is the drip batten on the deck of the roof to strengthen the installation later.

    Next, smear the adhesive material on some parts of the roof horizontally. Then, attach the rubber roof gradually. After some parts have been attached well, you can continue by attaching the next parts until the entire rubber roll is attached well. There is a possibility that some bubbles come out due to the glue that is not smeared thoroughly.

    How Do You Install Roofing On A Flat Roof Post

    Position the post perpendicular to the mark so one edge of the base plate is aligned with the chalk line. Use a socket wrench and ratchet to secure the base plate to the ceiling with a 3/16″ x 3″ screw in each hole cut in the base plate. Repeat the process and place the remaining grids on the breadboard layout and corresponding chalk lines.

    Read Also: How To Add A Gable Overhang

    Additional Tips For Installing Roll Roofing

    A few roll roofing additional details include:

    • Try to install the roll roofing material when the temperature is at least 50°F.
    • Clean the area of any sticks and stones beforehand and as you work. Also, install a drip edge along the edge of the roof.
    • With lower sloped roofs, you can install the material horizontally. With higher-sloped roofs, you should install them vertically.

    How Do You Install Roof Tiles On A Metal Roof

    Mobile Home Roof Systems

    Lay the tiles. Start on one side first and then go up through the roof. If you don’t have a batten installed, you can nail the tiles directly into the siding. If you installed the planks first, nail the tiles.

    Synthetic feltWhat are the advantages of synthetic roofing underlayment? There are four main benefits of laying a plastic roofing over felt. Compared to Synthetic Felt Roofing Underlayment: Synthetic roofing membranes have a strong and durable construction with extremely high tear resistance compared to felt.What is synthetic felt roofing?Unlike conventional roofing, synthetic siding is gene

    You May Like: Roof Overhang Extension

    Can You Put Roofing Tar Over Shingles

    However, the preferred method is to replace leaking shingles, either by removing damaged shingles and replacing them along with the underlying roofing felt, or by lifting the row of shingles just above the damaged area and adding new shingles and roofing resin to cover the ceiling. to seal completely. A leak.

    Is Rolled Roofing Cheaper Than Shingles

    Rolled roofing is the least expensive roofing material, even compared to low-cost composite shingles. All materials, even the nails, are inexpensive. Unlike shingles, which apply one by one, you can roll out a square of mineral surface rolled roof within minutes. Rolled roofing is easy to transport.

    Recommended Reading: Can You Put Skylights In A Metal Roof

    Can You Walk On The Roof To Inspect It

    Most roofing manufacturers confidently say that you can walk on the roof, but you should always double check first that it can bear your weight it just makes sense. Inspect the roof and its trusses first and then put your weight just on the edge of the roof to begin with.How much weight can a mobile home roof support?

    On average, the rate of load is 30 psf or pounds per square foot.

    Plan The Roll Roofing Job

    Installing Rubber Roofing over a Mobile Home That Leaks

    Plan the roofing job, the job sequence, the purchase of materials, and be sure you have all needed materials on hand before starting the job. The basic roofing sequence is

  • Inspect the condition of the existing roof and roof decking
  • Plan and schedule any demolition, removal of materials that must precede the new roof installation
  • Have roof protection tarps or other materials if the roof might be left open and incomplete across inclement weather
  • Measure the roof and calculate the materials and supplies needed: roofing, underlayment, lap sealant, flashings, nails
  • Install roofing underlayment
  • Install finish flashings or counter flashings where required
  • You May Like: Skylight On Metal Roof

    Good Luck With Your Diy Mobile Home Roof Over

    As previously mentioned, a DIY mobile home roof over has both immediate and long-term benefits. Depending on the damage thats already been done, you could save thousands in heating and cooling bills while also upping the resale value of your mobile home. We hope this guide has pointed you in the right direction!

    What Else We Do For You

    We are here to help you with building your kit, supplying your order in a timely manner and assisting you with support during the installation. Feedback from previous customers let us know that we have the solution mobile home owners are seeking. Join satisfied RoofWrap clients across North America and solve your roofing problems once and for all … at a price that makes big sense.

    You May Like: Extending Roof Overhang

    How Do You Install Rollroll Roofing

    Roll roofs are often installed on bare wood or primed siding. Pre-application of roofing material protects the coating better against condensation and against leaks. If the ceiling is sloping, you can use the bare-nail method. For a slightly sloping ceiling, use the concealed nail method shown.

    How to measure roof pitchWhat is the recommended roof pitch? Clapboard manufacturers recommend a slope of 4/12 or more, but the absolute minimum slope is 2/12. Slope is measured in inches of vertical roof rise over a horizontal distance of one foot .How do you figure out the pitch of a roof?Determination of the roof pitch. The angle or slope of a roof is calculated by the number of inches it increases vertically for every 12 inches hor

    What Kind Of Insulation And Installation Is Best For Each Section Of A Mobile Home

    Pin on Mobile Home Upgrades

    A lot goes into choosing the type of insulation youll need for your mobile home. First, you need to decide which kind of material is right for your home. Second, youll need to chose the kind of installation that is best for each area of your home.

    Once those two decisions are made youll need to hire an insulation installer or prepare yourself for an intensive DIY project. Depending on your material, you may need a contractor with specialized equipment or rent/buy your own.

    Well take a quick look at how this could look in different sections of your mobile home.

    Recommended Reading: How Often Should A Roof Be Replaced

    Cellulose: Recycled Paper Insulation For Mobile Homes

    Cellulose fibers can take the place of fiberglass fibers in insulation materials. Instead of glass, cellulose is made out of recycled paper that is concentrated down and then formed into fibers. Some other natural materials you might see for insulation include:

    • Cotton
    • Hemp

    Advantages: Cellulose is an environmentally-friendly option since its produced from recycled materials. Unlike fiberglass, it doesnt bear the risk of causing lung damage.

    Disadvantages: It has to be replaced every five years in many cases, especially if it absorbs water. Unlike fiberglass, it often requires a professional to install it.

    Do You Need Underlayment For Peel And Stick Vinyl

    Peel and stick vinyl plank flooring doesnt need an underlayment, which usually serves as a protective barrier between flooring and subflooring. However, some manufacturers recommend using a primer before installing peel and stick vinyl because it can improve how well the adhesive works, making the floor stick longer.

    Read Also: Roof Replacement Cost California

    Typical Roll Roofing Installation Steps & Specifications

    Weather conditions: for applying roll roofing: the roof should be clean and dry, and ambient temperatures should be at or above 50°F.Watch out: If you must install roll roofing at lower temperatures store it indoors and warm it to permit unrolling without cracking the material. We can sometimes spot roll roofing installed from too-cold rolls by later failures appearing as cracks, at regular intervals across the width of the material.

    Our photo shows our client pointing to a low slope area on a roof where mineral-granule coated asphalt roll roofing was applied after shingles in that location had leaked repeatedly.

    How Much Does A Mobile Home Roof Replacement Cost

    How to mobile home roofing video 1 of 1

    Mobile home roof replacement costs will vary according to the type of home and roofing materials used. With that said, most DIY homeowners can expect to pay between $1,500-$3500 for a standard metal or asphalt roof job on a manufactured home. Its also been suggested that a slightly peaked single wide mobile home can get a new asphalt shingle roof for about $3,000.

    For a more detailed cost estimate, take look at a mobile home roofing calculator and input your specific information. When it comes to larger mobile home repair expenses such as a roof replacement, it will always serve you well to do additional research so that your expectations are realistic and you can prepare yourself for the financial investment.

    Recommended Reading: Roof Cost California

    RELATED ARTICLES

    Most Popular